Features:

1. The products are made of high quality PCB material, and the quality is guaranteed
2. Stable product performance, long service life, shipping with electrostatic bag packaging protection
3. High current 40A
4. The electric regulator has the function of overheat and misoperation protection
5. Easy to use and operate, very suitable for DIY enthusiasts

Product parameters:

• Limit use: Continuous current 40A
• Voltage range: 4V-16V
• Color: Yellow

Number of batteries:

1. 4-12NIMH
2. 2-3LIPO (4LIPO does not allow BEC output)
3. BEC Output: consecutive 2A, (instant 3A)
4. 2LIPO 4-5 micro steering gear
5. 3LIPO 3-4 micro steering gear

Protection function:

• Automatic selection of 2-3LIPO, respectively, the protection voltage is 6V/9V;
• Automatic NIMH selection, each section protection voltage is 0.8V;
• Safe start, throttle position is not correct prohibit start;
• Temperature protection, 110 degrees surface temperature stop;
• Out of control protection, stop after 1 second without signal.

Performance description:Speed limit, 2 pole internal rotation up to 300,000 RPM, 12 pole external rotation 50,000 RPM, 14 pole external rotation 42,000 RPM.8KHz PWM control, using the speed control curve.Auto throttle ADAPTS for more remote control devices.Using BEC, the MCU separates the power supply and works more stably.Setting method:

1. Open the transmitter, push the throttle to (FUTABA series of transmitters need to select the throttle channel REV use).
2. Connect the receiver and motor.
3. Turn on the power supply, if the transmitter is normal, there is the following sound: (if the sound is no longer sound after the end of the sound is a long “beep” sound, then check the reverse setting of the transmitter throttle channel.)
4. B B indicates LIPO automatic protection
5. BB BB indicates NIMH /NICD automatic protection
6. BBB BBB stands for brake selection
7. When there is no action, all sounds continue to loop until an action is requested.
8. There are Settings you need during the sound cycle to quickly pull the throttle into position when you hear the syllable that prompts the sound (for example, select LIPO auto protection and pull the throttle into position when you hear a B). At the same time, the motor will make a very high-pitched sound to confirm.
9. At this point, if there are other Settings, quickly push the accelerator to do the next option selection.
10. If your setup is complete, wait 2 seconds for the motor to make the appropriate battery protection confirmation sound again and confirm the throttle position before you can use it.
11. LIPO automatic protection has only 2 protection voltage protection points, namely 6V and 9V, and the battery can be used unnecessarily on a fully charged battery.
12. NIMH automatic protection is calculated according to the actual number of batteries, each battery is set to 0.8V, in order to accurately judge the battery voltage, please fill the battery. If it is not full, the electrical regulator will estimate the protection voltage at 70% voltage. (You can also use this feature when using 4LIPO)

Brake:The factory Settings are none. A brake setting operation can be done during actual use, so that the motor uses the back electromotive force to brake after closing the throttle.If you want to remove this brake function, you can set a brake operation again, then the function is cancelled.Parameter reset function, because the electric thermostat has overheating and misoperation protection function, if you find that your electric thermostat acceleration, or steering, or throttle curve and other any characteristics and how the new time has changed, then you can do a parameter setting, in order to regain performance.When the device is powered on, it plays a long tone of B, indicating that the LIPO auto protection state is in. BBB plays three tones, indicating that the NIMH /NICD auto protection state is in.Warm reminder:40A electric modulation 2212 930KV 1000KV 1400KV motor