The V3 version has all the function of V2 board, also add the following 2 additional function.

• Add 8M Flash chip for Betaflight Black Box.
• 3 full UARTs (UART1, UART2 and UART6) are available in the V3 version. Pilots could use one UART for DJI digital FPV unitor Caddx Vista digital FPV unit and the other UART for external receiver like TBS Crossfire.

The V2 board only have one full UART and could not support DJI digital FPV VTX.

For a new generation of toothpickdronethis new AIO Brushless FC can handle 20A continuous current(25A burst), which is the first 20A All-in-one FCon the market.ComparedtoFC/ESC Stacksdesign, this board providedwith massive levels of performance capability while still maintain ultralight only 6.63g.Breaking through the limit of toothpick power, exploring more possibilities in 3”-4” drones. This board isyourbest choice toDIY your own toothpick drone that is tailored to your requirements.

If you are looking forwhoop version, pleaseclick here

Here is a video of detailed introduction for20A AIO FC, made byJon E5 FPV.

BULLET POINT

• This new board can handle 20A continuouscurrent(25A burst), which is the first 20A All-in-one FCon the market
• Comes with 4*Motor Pluggable Pins and NotPre-solder in default,fitsyour needs of self-assembly best
• Compatible with120X,130X, 140X motors, and1505 motors
• USB port is mounted on the side, youhave more possibilities of mounting it while still maintaining access to the USB port
• All of the solder pads are at the edge of FC, which is a convenience tosolder
• Double-sided motor solder pad. Pins pad and wires pad are both built-in for motors connection
• Integrated with a Betaflight MATEKF411 processor FC, Betaflight OSD,F4 MCU,and 20A ESC,support 2-4S battery

Comparison ofToothpick 12A AIO FCandToothpick 20A AIO FC

PARTS UPDATED

• Integrated24 singleN-channel MosFETs chips on20A AIO FC board,which has a lower inner resistance. 12A AIO FC board adopts 12 dual MosFETschips instead. Current sensor included.

Double-sided Motor Solder Pad
Support connect with motors via connectors or solder directly

Mounting Pattern and Real Holes of Mounting Holes
Thisboard comes with standard 26.5×26.5mm mounting holes, which can install easilyin most whoop and toothpick frames.

RECOMMENDED PARTS

• Motors:1505 Motorsand1404 Motors
• Propellers:HQ 3020 2-Blade Prop/HQ 3030 3-Blade Prop/HQ 4025 2-Blade Propellers

SPECIFICATIONS OF FC

• CPU: STM32F411CEU6 (100MHZ)
• Six-Axis: MPU6000 (SPI connection)
• Size: 32.5*32.5mm (26.5mm mounting holes)
• Firmware version: Betaflight MATEKF411 (MK41)
• OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
• Receiver:SupportFrsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/TBS CrossfireReceiver/DSMX Receiver
• Support programmable LED like WS2812 etc
• Built-in current sensor
• Weight: 6.63g

SPECIFICATIONS OF ESC

• Support BLheli/BLHELI_S suite Pass-through ready
• Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
• Input voltage: 2S-4S Lipo
• Continuouscurrent: 20A
• Peak current: 25A
• Firmware: BLHELI_S
• Motor Connectors: 1.25mm header pins connector

DIAGRAM FOR Toothpick F420A AIO FC V3

PACKAGE

• 1 * Toothpick F420A AIO 2-4S brushless flight controller
• 1 *Cable Pigtail (XT30)
• 4 * M2x10mm screws
• 4 * M2 nuts
• 4 * Anti-vibration rubber dampers
• 4 * Motor Pluggable Pins